Alarm Lock DL5300 Manual de instrucciones descargar pdf (Pagina 34)

ACCESS = Entry into a restricted area.

AUDIT TRAIL = A date/time stamped log of previous

lock events.

CLOCK

• REAL TIME CLOCK = An accurate built-in clock

that allows date/time stamping of events. The

clock can be slowed or speeded up to fine tune

long term accuracy to within three minutes per

year.

• CLOCK SETTINGS = Printout includes date,

time, weekday, and clock speed.

• CLOCK SPEED = The clock can be adjusted to

allow faster/slower speeds and therefore

increasing clock accuracy.

CODE = Numeric sequence of numbers (such as:

1234) entered at the keypad. If Star-Enter-Key is

required, must be followed by a [:] key.

• BASIC USER CODE = User Codes assigned to

User Numbers 12+ (except Users 297-300).

(Does not allow programming)

• INSTALLER CODE = User Codes assigned to

User Numbers 2 and 3. (Allows all programming

except Master functions).

• INVALID CODE = A User Code that has not been

programmed in the lock.

• MANAGER CODE = User Codes assigned to

User Numbers 4 through 6. (Allows most of the

programming functions).

• MASTER CODE = User Code assigned to User

Number 1. Default (factory) Master Code is

123456. The User with the Master Code has

complete control of the lock.

• PRINT ONLY USER CODE = User Code as-

signed to Users 10 and 11. (Allows no

programming except print functions).

• QUICK ENABLE USER 300 CODE = Refers to

the User Code entered by User 297 which

(when entered at the keypad) enables the User

Code assigned to User 300 for one time only.

• QUICK PC ACCESS CODE = Permits upload/

download to DL-Windows Software on IBM/

compatible computer running Microsoft Windows

95, 98, or NT 4.0. Refers to the User Code for

User 298.

• SERVICE CODE = User 300 User Code. Allows

only one entry, then needs to be re-enabled by

the User 297 User Code to regain access.

• SUPERVISOR CODE = User Codes assigned to

Users 7, 8 and 9. Can only program day-to-day

operation.

• USER CODE = Code used by Users. Code is 3

to 6 numeric digits long, allowing controlled

entry.

• VALID CODE = An entered User Code that has

been programmed in the device.

COM PORT = A computer serial communications port

used to communicate with the Lock and/or Data

Transfer Module.

DATA TRANSFER MODULE = A device that permits

transfer of program/data between a computer and

the lock.

DATE = Month, Day and Year entered as MMDDYY.

DAY OF WEEK = Sunday through Saturday (where 1

= Sunday and 7 = Saturday).

DEFAULT = Default settings are the original settings

that were set at the factory; in other words, it is the

lock's original factory condition when the lock was

first taken out of its box. The default settings are

permanently encoded within the lock's fixed mem-

ory, and when the lock is first started, or when

power is removed and re-applied (see Wiring and

Power-Up, page 11), the original factory default set-

tings are re-loaded and take effect.

DISABLE = Turn off.

DOOR NUMBER = Identification of each door with a

specific number (1-96). (Used with AL-DTM

Transfer Module)

DOWNLOAD = Send data to lock or AL-DTM.

ENABLE = Turn on.

EVENTS = Recorded lock activity.

FUNCTION (also called Programming Functions) =

are the numbers used to program lock features

(enabling/disabling Users, User Groups, Passage

Mode, Schedules, etc.).

GROUP

• USER GROUP = Defining a User to specific

Groups, allows User entry when the Group is

allowed entry.

• GROUP 1 DISARMS BURGLAR CONTROL = A

Group 1 USER CODE entry can disarm an

Glossary

1 2 ... 29 30 31 32 33 34 35 36

Comentarios a estos manuales

Sin comentarios

Alarm Lock DL5300 Manual de instrucciones Pagina 34

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Alarm Lock DL5300