Alarm Lock 710 Instrucciones de operaciones descargar pdf (Pagina 3)

INSTALLATION & OPERATING INSTRUCTIONS

ELECTRONIC PANIC LOCK MODELS 700, 700L, 710 & 710L

INSTALLATION

1) With the door closed, select the proper template and tape it to the inside face of the door with the center line approxi-

mately 38" above the floor per template directions.

2) Mark and drill the following holes (see template for details):

A) FOR SINGLE AND DOUBLE DOORS: Mark six (6) .157" dia. holes, four (4) for the lock mounting plate and two (2)

for the keeper.

B) Mark a ¼" dia. hole for the rub plate on double doors 1¾" thick only.

C) IF OUTSIDE CYLINDER (CER-OKC) IS USED: Mark the center of the 1¼" dia. hole.

D) IF OUTSIDE PULL MODEL 707 IS USED: Mark the center of the four (4) ¼" dia. holes.

E) If mounting the lock on a hollow metal door and wires are to be run through the door, drill hole x (see template).

NOTE: If outside pull is used, drill four (4) holes ¼" dia. through the door from the inside. Then drill ¾" dia. holes 1¼"

deep from the outside of the door.

3) Remove the lock cover and four (4) screws holding the cylinder housing to the bolt cover. Install rim cylinder (CER) with

the keyway horizontal, facing the front of the lock (nine o'clock position) and cut the cylinder tailpiece 3/8" beyond the

base of the cylinder. Reinstall the cylinder housing, guiding the tailpiece into the crosshole of the cam with four (4)

screws.

4) Use the key to test for proper operation of the deadbolt. The key should be able to be withdrawn from the lock in either

the fully locked or fully unlocked position of the deadbolt. If not, the cylinder and the cam are misaligned and the cylinder

housing must be removed. Turn the cam a quarter (¼) turn to the right, and reinstall the cylinder housing. (NOTE: The

deadbolt can be projected into the keeper by turning the key counter-clockwise and can be withdrawn from the keeper by

turning the key clockwise one full turn.)

5) FOR OUTSIDE CYLINDER ONLY (CER-OKC): Install the rim cylinder with the keyway horizontal facing the front of the

door (three o'clock position) with the screws supplied and cut the tailpiece 3/8" beyond the inside face of the door.

6) FOR OUTSIDE CYLINDER ONLY: Guide the tailpiece of the outside cylinder into the crosshole of the outside cam.

7) Install the lock to the door with four (4) #10 screws as supplied. Do not tighten them at this time.

8) Insert the bar and channel assembly under the retainer bracket which is mounted to the lock baseplate. Hold the bar and

channel assembly horizontally against the door using a level. Slide the end cap bracket into the end of the channel and

using the bracket as a template mark and drill the two (2) .157" dia. mounting holes on the door. NOTE: If channel is too

long, cut the channel and channel insert to the proper length and deburr edges.

9) Attach the pushbar to the lock at the clapperarm hinge bracket using the 10-32 x 1/2" screw and #10 internal tooth lock-

washer provided.

10) Mount the end cap bracket to the door with two (2) #10 screws provided, and tighten the lock securely to the door.

11) Attach the end cap to the end cap bracket using the 10-24 x 1/2" oval head screw provided.

12) FOR SINGLE DOOR ONLY: Remove the keeper cover, roller, and pin. Install the keeper base on the door with two (2)

screws supplied. Reinstall the pin, roller and cover with two screws.

FOR DOUBLE DOOR ONLY: Install the rub plate for a 1¾" wide door, from inside the door. Also install the 732 keeper

with two (2) #10 screws supplied. Do not tighten the screws fully because the keeper will require adjustment as men-

tioned in instruction 13.

13) FOR SINGLE DOOR ONLY: Close the door, project the deadbolt and adjust the keeper so that the door is tightly latched.

Retract the deadbolt, hold the keeper, release the latch and open the door. Open the keeper cover and tighten the

screws. Drill a .157" dia. hole, as shown on template, for the holding screw, and fasten the keeper with a #10 screw. Re-

install pin, roller and cover with two screws.

FOR DOUBLE DOOR ONLY: Close the door, project the bolt and adjust the plastic slide on the 732 keeper so the door is

tightly latched and tighten the screws.

1 2 3 4 5 6

Comentarios a estos manuales

Sin comentarios

Alarm Lock 710 Instrucciones de operaciones Pagina 3

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Alarm Lock 710