Alarm Lock Trilogy DL3000 Series Manual de instrucciones

1 Trilogy PDL3000, PDL3500 & ETPDL Programming Instructions HID HID CORPORATION PROXCARD® PROXKEY® KEYFOB PDL3500 ETPDL PDL Trilogy Series Stand-

10 NOTE: The AL-PCI cable is designed to be used on a 9 pin serial COM port. If your computer has a 25 pin COM port, a 25 pin to 9 pin adapter must

11 WIRING See the Installation Manual for more information. Batteries: Use only 1.5 volt Duracell Alkaline size-AA batteries. External Power: Red /

12 Quick Start First Time Start Up 1. Unpack the lock. 2. With the batteries disconnected, hold down the ; key for 10 seconds and release. 3. Co

13 Quick Start (cont’d) Delete a User Code 1. Enter Program Mode (if not in already). 2. Press ; 2 ; [User Number] :. The lock will flash

14 Verifying Basic Keypad User Codes Test a valid User Code: VALID CODE - The Green LED will flash momentarily and the sounder will beep a few times

15 Function 1 Change Master Code See page 16 Function 2 Add/Delete/Change User Codes See page 16 Function 3 User Disable (By User Number) See page

16 1. New Master Code (User Number 1) 2. Add/Delete/Change User Codes 2-2000 ; 1 ; [ _ _ _ _ _ _ ] ; [ _ _ _ _ _ _ ] : (New Master

17 USERS (Continued) ; 6 : 6. Enable Total User Lockout Mode (This Function enabled through keypad only) 7. Disable Total User Lockout Mode (This Fun

18 ; 1 2 ; 0 0 0 : 12. Clear All Schedules and Timeout Functions Function 12 clears all programmed Schedules and all Timeout Functions. (To cle

19 GROUPS Group Enable/Disable with Timeout (Enter Timeout, XXX Hours) (Functions 25-34 are enabled through the keypad only) • Hours must be between 1

2 Table of Contents PDL Series Lock Features ... 3 Supported Products ... 4 Lo

20 ; 3 8 ; [ _ _ _ _ _ _ ] : (Date) 38. Set Date • Use Month Day Year format - MMDDYY - Single digit months and days are entered with a preced

21 ; 4 5 : 45. Enable Passage Mode (This Function enabled through keypad only) ; 4 6 : 46. Disable Passage Mode (This Function enabled through keypad

22 49. Disable Permanent Passage Mode (This Function enabled through keypad only) 50. Return Lock to Normal Passage Mode Schedule (This Function enabl

23 ; 5 5 : ; 5 7 : 57. Print Clock Settings, Software Version and Door Number 55. Print Audit Trail ; 5 6 : 56. Print User Code List ; 5 8 : 58.

24 60. Number of Attempts Before Lockout 61. Set the Attempts Lockout Time • Number of attempts before lockout must be 1-9 attempts. • The number of

25 ; 6 7 ; [ _ _ ] : (Event Number) 67. Add System Features SYSTEM FEATURES 68. Delete All Relay Features added by Function 67. ; 6 8

26 Scheduled Passage and Group Use the functions below to enable Passage Mode and enable/disable Groups at the time programmed. • For day enter: 1 for

27 QUICK SCHEDULES 84. Business Quick Schedule 7AM-5PM, Monday - Friday (This Function enabled through keypad only) ; 8 4 ; [ _ ] : (Group) ; 8

28 To Disarm a Burglary Control Panel 90. Relay Activation (Open Time Window) ; 9 0 ; [ _ ] ; [ _ _ _ _ ] :

29 ; 9 9 ; 0 0 0 : 99. Clear All Lock Programming (This Function enabled through keypad only) Clears all programming, and returns lock to factor

3 Audit Trail • 40,000 Event Capacity • Entries Logged with Time and Date • Critical Programming Events Logged • Printable using the AL-IR1 Hand-Held

30 Groups and Scheduled Group 1 Examples The following examples detail the more advanced features of the PDL series locks. Although all features and

31 Groups and Scheduled Group 1 Examples (cont'd.) Functions 90/91: Use Function 90 and 91 (see page 28) to create a window of time where if any

32 Function Number(s) Function Name Programming 43/44 Clock Adjust 52/53/54 Pass Time (3 sec)  10 sec  15 sec  60 Set Locko

33 User Number (1-2000) User Code (3-6 digits) User Name 1 2 3 4

34 Day(s) Function Number Up to 500 scheduled functions can be programmed (Up to only 150 using AL-DTM2). For Day Enter : 1 = Sunday, 2 = M

35 ACCESS = Entry into a restricted area. AMBUSH = A special Code entered at the keypad when the User is forced to unlock a device. The device unlock

36 PROGRAM MODE = A mode allowing program/data to be entered through the keypad. Only specific Users can program a lock manually, by entering their U

4 Supported Products Data Transfer Module (AL-DTM) An AL-DTM can be used to transfer Lock Programs (and other data) between DL-Windows and locks. Wh

5 Lock Design Overview Why Use Software inside a Lock? With ordinary door locks, the need to make physical copies of metal keys and distributing them

6 Terminology Used in this Manual What is a Lock Program? A Lock Program contains the instructions that a lock uses to per-form its various functions.

7 2000 Users in its programming memory. This memory can be thought of as simply a numbered list from 1 through 2000. Each entry in the list is repre

8 USER TYPE USER NUMBER GROUP DEFAULT ASSOCIATION MINIMUM PROGRAM LEVEL (See page 6) Master Code 1 - M Installer Codes 2 & 3 none 4 Manag

9 ACTIVITY LED SOUNDER COMMENTS Keypress 1 RED Flash 1 Beep Normal Operation Access Granted or Remote Release 3 GREEN Flashes 3 Beeps Remote