Alarm Lock NETWORXPANEL Manual de instrucciones descargar pdf (Pagina 34)

ACCESS = Entry into a restricted area.

AMBUSH = A special Code entered at the keypad

when the User is forced to unlock a security device.

The device unlocks but sends a silent alarm with no

indication at the keypad. Can be used to trip a re-

lay, to alert security, or trip a silent alarm on a Bur-

glary Alarm control panel.

AUDIT TRAIL = A date/time stamped log of previous

NETWORXPANEL events.

BURGLARY CONTROL PANEL = Provides local

alarm and remote communication to request secu-

rity for burglary/break-in. The integral NETWORX-

PANEL relay output used for Ambush can provide a

silent alarm and call-for-help.

CLOCK

• REAL TIME CLOCK = An accurate built-in clock

that allows date/time stamping of events. The

clock can be slowed or speeded up to fine tune

long term accuracy to within three minutes per

year (see Functions 43 and 44).

• CLOCK SPEED = The clock can be adjusted to

allow faster/slower speeds and therefore increas-

ing clock accuracy (see Functions 43 and 44).

CODE = Numeric sequence of numbers (such as:

1234) entered at the keypad. If Star-Enter key is

required, must be followed by a : key.

• AMBUSH CODE = See Ambush.

• BASIC USER CODE = User Codes assigned to

User Numbers 12+ (except Users 297-300).

(Does not allow programming)

• INSTALLER CODE = User Codes assigned to

User Numbers 2 and 3. (Allows all programming

except Master functions).

• INVALID CODE = A numeric sequence of num-

bers entered via the keypad buttons that have

not been programmed into the lock programming.

• MANAGER CODE = User Codes assigned to User

Numbers 4 through 6. (Allows most of the pro-

gramming functions).

• MASTER CODE = User Code assigned to User

Number 1. Default (factory) Master Code is

123456. The User with the Master Code has

complete control of the NETWORXPANEL pro-

gramming.

• QUICK ENABLE USER 300 CODE = Refers to

the User Code entered by User 297 which (when

entered at the keypad) enables the User Code

assigned to User 300 for one time only.

• SERVICE CODE = User 300 User Code. Allows

only one entry, then needs to be re-enabled by

the User 297 User Code to regain access.

• SUPERVISOR CODE = User Codes assigned to

Users 7, 8 and 9. Can only program day-to-day

operation.

• USER CODE = Code used by Users. Code is 3 to

6 numeric digits long, allowing controlled entry.

• VALID CODE = A numeric sequence of numbers

entered via the keypad buttons that have been

programmed in the lock programming and identi-

fied by the NETWORXPANEL as a User Code.

DATE = Month, Day and Year entered as MMDDYY.

DAY OF WEEK = Sunday through Saturday (where 1 =

Sunday and 7 = Saturday).

DEFAULT = "Default" settings are the original settings

that were set at the factory; in other words, it is the

original factory condition of the NETWORXPANEL,

NETPDK or NETDK when it was first taken out of its

box.

DISABLE = Turn off.

DOOR AJAR = The controlled door was unlocked and

is held open for a certain period of time. If the

length of time is longer than the allowed Door Ajar

Time (programmed at function 68) the Aux Relay

will engage for 2 seconds (function 67 #12) or trig-

ger the Alert Sounder (function 67 #41). Note: The

programmed Door Ajar Time begins after the pro-

grammed Pass Time ends (Pass Time settings are

controlled by Functions 52-54).

DOWNLOAD = Send data to the NETWORXPANEL.

EMERGENCY COMMANDS = For use with all keypads

enrolled into the Trilogy Networx™ wireless network

only. Wireless commands can be sent to all wire-

less locking devices in an Account during a crisis or

other urgent situation. "Global Lock Down" locks all

doors in the Account; "Global Passage" unlocks all

doors in the Account; Return all devices in the Ac-

count to "normal" discontinues all emergency com-

mands, reverting to "normal" non-emergency opera-

tion. Note: DL-Windows does not need to be run-

ning to allow these "Emergency" commands to be

initiated; any wireless keypad can be used to dis-

seminate these commands throughout the wireless

system.

ENABLE = Turn on.

EVENTS = Recorded NETWORXPANEL activity.

FUNCTION (also called Programming Functions) =

Glossary

1 2 ... 29 30 31 32 33 34 35 36

Comentarios a estos manuales

Sin comentarios

Alarm Lock NETWORXPANEL Manual de instrucciones Pagina 34

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Alarm Lock NETWORXPANEL