Alarm Lock Trilogy DL4500 Manual de instrucciones descargar pdf (Pagina 24)

68. Delete All Relay Functions and System Options added

by Function 67. Also Privacy Time-Out Duration.

; 6 8 ; [ _ _ _ ]

(3-digits)

Enter

;

to delete all Relay Functions and System Options added by

Function 67.

Note:

Programming "000" does not affect existing "Privacy Time-Out Duration" settings, described below.

When using a DL4100 or DL4500, enter a number between 001-250 for Privacy Time-Out Duration, in minutes (be sure to enter 3 digits).

This Privacy Time-Out Duration is the maximum time lock will remain in Privacy Mode, before returning to standard operation (defaulted

to 10 minutes).

Privacy Terminated on Exit Only

Enter 251 to

disable the Privacy Time-Out Duration

: Privacy will last indefinitely until either the inside lever is turned or until a Master or

valid Manager User Code is entered at the keypad. In addition, the flashing LED is disabled.

Note:

Existing "Privacy Time-Out Duration" settings are not affected by subsequent programming of "000" (which is used to delete all

relay functions and system options added by Function 67).

Note:

The factory default is set to "Residency Feature" for the DL4500 and "Privacy Feature" for the DL4100. Entering

;

will clear the factory default of the lock. To re-program factory default, see page 11.

Note:

To maintain backwards compatibility, entering

;

or entering

;

will delete all Relay Functions and System Options added by Function 67.

Programming Functions (cont'd)

;

[ _ _ ]

(Event Number)

67. Add System Features

SYSTEM FEATURES

• Relay Features

(12-24. Reserved)

Use Function 67 to program

one or more

lock events and the Relay will energize when the programmed event(s) listed below oc-

curs. For example, program

;

and when an attempted entry fails (such as a User who enters an

incorrect or un-programmed User Code), the Relay will energize for 2 seconds.

Failed attempted entry.

Relay energizes for 2 seconds when an

attempted User Code entry via the keypad fails.

Scheduled Unlock Event.

Relay energizes for 2 seconds when

lock is unlocked by a schedule

Disabled User or Group.

Relay energizes for 2 seconds when a

disabled User or disabled Group member enters a User Code.

Lock Out.

Relay energizes for 2 seconds when a Lock Out occurs

(i.e. number of attempts is exceeded, see Function 60).

Follow Access Granted.

When a valid User Code is entered into

the keypad and the lock unlocks, the Relay energizes for 2 seconds.

Compare with Event 31.

10.

Ambush.

Relay energizes for 2 seconds when Ambush is tripped.

See Function 66, page 25.

Group 1 User Code.

Relay energizes for 2 seconds when a sched-

uled Group 1 User Code is entered. See Function 90, page 29.

11.

First Key Press.

Relay energizes for 2 seconds at the first key

press of any sequence.

Scheduled Lock Event.

Relay energizes for 2 seconds when lock

is locked by a Schedule.

31.

Follow Access Granted--No Time Limit.**

When a valid User

Code is entered into the keypad and the lock unlocks, the Relay

energizes for the

same amount of time as the programmed Pass

Time

. (The Pass Time is the length of time the lock stays

unlocked after a valid User Code is entered. See functions

52-54). Use this feature for remote monitoring or other activation.

• System Options

25. Disable Sounder

26. 5 sec. Delayed Entry *

27. 15 sec. Delayed Entry *

28. 45 sec. Delayed Entry *

* Features 26, 27 & 28 will delay User Codes 12 and higher only (except 297, 298 and 299).

** Feature 31 should be used with External DC Power unless feature is used for short a duration and infrequently (sustained closure of relay will drain

batteries).

NOTE:

Enter

;

to delete all Relay Features added by Function 67 (identical to Function 68).

Ambush Function

Connect relay to a device able to properly monitor dry contacts for an

Ambush

condition.

Program the Relay for

Ambush Tripped

using Program Function 67(10) above.

Set the Ambush Code using Program Function 66.

When the Ambush Code is entered followed by a valid User Code, the relay will close for 2 seconds.

Notes:

The Ambush Code defaults to

. An error will sound if you try to program a new User Code starting with the Ambush Code.

• Privacy/Residency Features

35. Disable Keypad on Deadbolt (DL4500) or Button

Press (DL4100). (Often used for bathroom doors).

36. Cancel Passage on Deadbolt (DL4500) or Button

Press (DL4100)

37. Leave Unlocked on Exit (Passage)

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 39 40

Comentarios a estos manuales

Sin comentarios

Alarm Lock Trilogy DL4500 Manual de instrucciones Pagina 24

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Alarm Lock Trilogy DL4500