Alarm Lock ETPLN Guía de usuario descargar pdf (Pagina 33)

DL-WINDOWS™ for Trilogy Networx™ V4.0 USER'S GUIDE 33

Use DHCP (Dynamic Host Configuration Protocol) is enabled

by default. When checked and Save Configuration is

clicked, DL-Windows allows the selected Gateway to accept

the dynamic assignment of an IP address by the TCP/IP

network. Check Use DHCP to remove the need to manually

assign a static (fixed) IP address to the Gateway (note that

Emergency Commands will NOT work). Uncheck Use DHCP

to allow the manual assignment of a static IP address to the

selected Gateway (a warning popup appears [shown on page

8] warning that the Gateway may be unreachable until it is

installed on the correct network or is manually defaulted).

See your network administrator for additional information.

Use DHCP

Tools > Configure Network Settings

The Network Configuration screen displays the various networking attributes required for the selected Gateway to work

correctly within the current wireless network. See your network administrator for more information if needed.

Note: For wireless security, because the communications between the network/router and the Gateway conform to the AES

(Advanced Encryption Standard), we recommend leaving the system unsecure, but to use MAC address filtering within the router

software (if your router supports MAC Address filtering). Using this kind of security is easier to setup and more secure than using

the security protocols (encryption methods) shown within this screen.

To open this screen, click the GW Confg button to open the Gateway Configuration screen. Click to

highlight a specific Gateway in the list, then click Tools, Configure Network Settings.

Wireless Mode

IP Address

Subnet Mask

Network Type

Network Name (SSID)

The Gateway module acts as an interface between a computer

network and the Networx

™

wireless locks. Of the two Gateway

models available ("Wired" or "Wireless/Wired"), the "Wireless/

Wired" Gateway model supports connection to a network using

the 802.11 standard. This field allows you to specify the SSID

(Service Set IDentifier) name assigned to the wireless Wi-Fi

(802.11) network. All "Wireless/Wired" Gateway models in a

system must use this name to allow for network

communication. Note: This field is case-sensitive and can

be up to 32 bytes in length. In addition, the Wireless Mode

pull-down menu in this screen must be set to Wireless Only

for this field to become active.

DHCP Name

Configures the selected Gateway for either wireless or wired

communication with the computer network. Select either Wired

Only or Wireless Only from this pull-down menu. If Wireless

Only is selected, the Wireless Network fields located in this

screen become active and available for selection.

To aid in locating the Gateway on the network, specify a name

to describe the domain name (host name) of the corresponding

IP Address assigned to the selected Gateway. The DHCP

name entered here will be used for the DNS configuration.

If the Use DHCP (see above) is unchecked, this field allows

the IP address to be manually assigned to the selected

Gateway.

To improve performance, network administrators determine

how best to divide their network. Create more hosts and

fewer subnets or more subnets and fewer hosts? The IP

protocol makes use of a Subnet Mask to more efficiently

route packets to their correct network destinations. When a

Gateway receives a data packet, the Subnet Mask indicates

how many bits of the packet's destination address are to be

used for routing and which bits are to be "masked" (ignored).

Use DHCP (see above) must be unchecked before data can

be entered into this field. This information must be obtained

from your network administrator.

Default Gateway

This field is the IP address of the physical device, such as a

router, for the current subnet to which you want to be

connected. This field is not to be confused with the IP

address of the Alarm Lock Gateway device installed in the

system. Use DHCP (see above) must be unchecked before

typing the IP address. This information must be obtained

from your network administrator.

Click this pull-down menu to select the network

communication mode. With "Infrastructure" selected, the

Gateways communicate to a wired LAN via access points.

With "Ad Hoc" selected, the Gateways can communicate

directly in a peer-to-peer fashion. Contact your network

administrator for more information.

(continued)

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 67 68

Comentarios a estos manuales

Sin comentarios

Alarm Lock ETPLN Guía de usuario Pagina 33

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Alarm Lock ETPLN